Obsidian Aurora Epoxy Flooring logoObsidian Aurora Epoxy FlooringAurora, IL
(331) 256-2716Contact us
Metallic Epoxy · Aurora

Metallic Epoxy Floors in Aurora, IL

We pour and swirl metallic epoxy by hand in Aurora homes and shops, then we seal that depth under a clear polyaspartic topcoat so it holds up to daily use.

❦2 days installs · typical timeline
Free Quote

Free Metallic Epoxy quote.

We reply within 1 business hour. No spam, ever.

Metallic epoxy floor with copper swirl and gloss.
Wide room with copper and slate metallic epoxy.
Trowel swirling metallic mica in wet epoxy.
What we install

What a metallic floor actually is, on the slab

Metallic epoxy starts the same way every floor we pour does, with bare clean concrete and a diamond ground profile. The difference is the pigment. We blend mineral mica into clear resin, then we move it across the slab by hand while the resin is still wet, working the swirl in the few minutes the chemistry gives us. The mica catches light at different angles, so the floor reads with real depth instead of one flat color. No two pours look the same. That is the whole point of a metallic floor.

On an Aurora slab this matters more than people expect. Our winters drag salt and grit through the door, and a flat coating shows every mark, every drip, and every tire ghost the season leaves behind. A metallic field hides the small stuff because your eye is already busy reading the swirl. We see it most in finished basements near the Fox River, in show garages off Galena Boulevard, and in retail entries downtown. The look is loud. The build under it is the same tough resin and polyaspartic we run on a plain garage floor, so you get the drama without giving up the toughness.

  • Common blends here run copper over slate, polished nickel, storm blue, and warm walnut.
  • Sealed under polyaspartic, so it takes the same chemical and daylight abuse as any floor we build for an Aurora owner.
  • Every floor is one of a kind, since the swirl is moved by hand in a short wet window and never repeats.
  • A strong fit for a finished basement bar, a polished garage, or a commercial entry foyer that needs to make a first impression.
  • We pour, swirl, and seal it ourselves, and we answer the phone when you call with a question about it.
A metallic floor is part craft and part chemistry, and we treat the swirl like the one shot it really is.

The wet window is short, so the swirl has to happen fast and with intent. One of us pours the base while another works the mica with a trowel and a leaf blower, reading the floor as the pattern opens up. We sometimes drop alcohol to open round cells that look like natural stone. Then we walk away and let it cure overnight. The next day we come back and seal the whole thing under clear polyaspartic, which is what gives the floor its glass depth and its grip.

If you want a floor that does more than cover the concrete, call us and we will bring real samples out to your Aurora address. We will look at the room, check the light through the day, and tell you straight what a metallic pour will do on your slab.

Materials

How the metallic layer is actually built

The metallic look is built in layers, not in one coat. First we grind the concrete down to a clean profile so the resin can bite into it. Then we roll a pigmented base coat that sets the floor's main tone. While that base is still open and wet, we pour and move the metallic resin on top, working the mica with trowels and blowers until the swirl looks right to the eye.

Color choice drives the whole job. A copper blend reads warm and busy. A slate or storm blue blend reads calm and deep, and it tends to suit a quiet basement room. We mix the metallic to the room itself, not from a fixed chart, because the same pigment shifts under bright daylight versus warm bulbs at night. Once the swirl cures, the clear polyaspartic topcoat locks it in and pulls the depth forward.

  • Mineral mica suspended in clear resin, moved by hand during the short wet window.
  • A pigmented base coat sets the floor's main tone before the metallic layer ever goes down.
  • The 3D depth only reads right under a clear polyaspartic topcoat that pulls the light through it.
  • Alcohol drops open round cells that mimic the look of natural stone.
Metallic epoxy floor edge where it meets the wall.
Close-up of swirled mica in cured metallic resin.
What about the alternatives?

Metallic versus the other designer floor options

People weighing a metallic floor usually look at a few other designer options first. Here is how we see each one stack up for an Aurora home or shop.

Acid stained concrete

Earthy and low cost, but the color sits thin and it shows wear fast once the sealer starts to break down.

Acceptable

Polished concrete with dyes

Clean and durable for a big commercial floor, though the finished look stays flat next to a real metallic swirl.

Recommended

Terrazzo style epoxy

Beautiful and genuinely unique, yet slow to install and costly, which puts it out of reach for most homes.

Acceptable

Full decorative flake

Our most popular garage finish, tough and forgiving, just without the deep liquid look that metallic gives you.

Recommended

Metallic epoxy and polyaspartic

The deepest look we pour, sealed hard for daily use, and the right call when you want the floor itself to be the feature.

Recommended
How it goes

From quote to walk-on, fast.

01

Your inquiry

Call or send the short form with what is going on at your place. A sentence or two is plenty for the first step.

02

We talk it through

We go over the situation on the phone, ask the questions that matter, and tell you what we would do next.

03

A clear plan

You get a plain-language rundown of the work, the order it happens in, and what to expect on the day.

04

The work gets done

Our crew shows up when we said, does the job, and walks you through the result before leaving.

Before you book

Questions to push on before booking the install

A metallic floor is a design choice, so ask the right questions before you commit to it. These are the ones we actually want you to push on.

Are real samples reviewed in the actual room's lighting?
Yes. We bring cured sample boards out to your Aurora home and set them down in the room where the floor will go. Daylight from a window and warm bulbs at night will both change how the metallic reads, so you should always judge the color in the space, not on a screen.
How much does it vary from one floor to the next?
A lot, and on purpose. The swirl is moved by hand in a short window, so your floor will never match a photo exactly. We talk through the general pattern and tone you want, then we pour to that direction. If you need a uniform look across a huge area, a flake floor may suit you better.
If a scratch or gouge happens, what is the repair plan?
The polyaspartic topcoat takes the daily hits, so most marks are surface only. A deep gouge can be sanded local and recoated, though a metallic blend is harder to bring back than a solid color. We walk you through exactly what a repair looks like before you choose this finish.
Does it work in a humid Aurora basement?
It does, as long as the slab is prepped right. We test the concrete for moisture first, since a wet slab will push a coating loose over time. If your basement near the Fox River runs damp, we set a moisture barrier into the system before the metallic ever goes down.
How does the color hold up under daylight?
The clear topcoat carries a UV stable layer, so the metallic tone holds far better than a bare pigment would. In a garage with a wide door open all summer you may see a slight shift over many years. In a basement or interior room the color stays put.
Aftercare

Keeping the depth visible across the years

A metallic floor is easy to keep, but the deeper the gloss, the more it shows. A little routine keeps the swirl looking wet and rich for years. Here is what we tell every Aurora owner after we hand the finished floor back.

  • Sweep once a week. The deeper the gloss, the more each micro scratch shows.
  • Damp mop once a month with a pH neutral product. Skip the abrasive scrub pads.
  • Put soft pads beneath chair legs and weight bench feet. Slip one under any heavy thing you slide across the floor.
  • Knock road salt and grit off your shoes in winter, since both act like sandpaper underfoot.
  • Wipe spills when you see them, even though the sealed surface gives you plenty of time to react.
Metallic epoxy floor with copper swirl and gloss.
How a finished metallic install reads in the room
FAQ

Frequent metallic epoxy questions

Do you install epoxy flooring across the Aurora area?
Yes. We install epoxy flooring throughout Aurora and the nearby Kane County and Kendall County towns, including North Aurora, Montgomery, Oswego, and Naperville. Our own crew does the prep, the pour, and the finish, and we pick up the phone when you call. Set a time with us and we will come read your concrete in person.
What separates epoxy from polyaspartic, in practice?
Epoxy lays down a thick, hard base that grips clean concrete and gives the floor its body. Polyaspartic is different. It cures fast, sometimes in a single day, and it holds its color better under harsh light. On most Aurora garage floors we combine the two, so you get a tough base under a quick, durable top coat.
How are coating jobs typically priced in this market?
It depends on the floor. Size is the biggest factor, and the condition of your slab matters too, since cracks and worn old coatings call for extra prep. The system you choose shifts things as well, because a plain solid color is simpler to install than a metallic or flake finish. We measure the space, read the concrete, and walk you through the full scope before any work begins.
Are winter installs realistic in the Aurora area?
They are. Aurora winters bring real cold and snow, so we track the slab temperature and the humidity before we coat anything. A heated garage helps a lot. Some polyaspartic systems also cure well in cooler air, and we time the work so your epoxy flooring sets correctly through the colder months.
Will the floor pick up or stain under hot tires?
A fully cured floor resists hot tire pickup, the problem where warm rubber tugs at a weak finish. Prep is everything. We grind the concrete to a clean profile and let each coat cure fully before you park on it. We also lean on polyaspartic top coats, since they shrug off heat and harsh stuff. Done right, your epoxy flooring stays put and wipes clean.
Ready when you are

Let's make your next steps easier

Tell us what is going on at your Aurora home and we will walk you through the options. One call or one short form is all it takes.

Call (331) 256-2716Make your inquiry
CallContact us